机械专业术语 组装、冲压、喷漆等专业词汇 Assembly line组装线
Layout布置图 Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪 Screw driver起子 Electric
screw
driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合
fuse machine热熔机
repair修理 operator作业员 QC品管
supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner
parts
inspect内部检查 thumb screw大头
螺丝
lbs. inch镑、英寸
EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试 Voltage switch of SPS
电源电压接拉键 sheet metal parts 冲件
plastic parts塑胶件
SOP制造作业程序 material
check
list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部
QC Section品管科 stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备 uncoiler and straightener整
平机
punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer
|'plein|刨床 miller铣床 grinder磨床 driller 钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager=vice manager副理 section
supervisor课长 deputy
section
supervisor副课
长 vice section
superisor副课长
group
leader/supervisor组长
line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库
pack packing包装 to apply oil擦油 to file burr 锉毛刺
final inspection终检 to connect material接料 to
reverse
material 翻料 wet station沾湿台
Tiana天那水 cleaning cloth抹布
to load material上料 to unload material卸料 to return
material/stock
to退料 scraped |'skræpid|报废
scrape ..v.刮;削 deficient purchase来料不良 manufacture
procedure制程 deficient manufacturing procedure制程不良 oxidation |'
ksi'dein
|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective
to
staking铆合不良 embedded lump镶块
feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and
training教育与
训练 proposal improvement提案改善 spare parts=buffer备件
forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of
a
department部门
名称
administration/general
affairs
dept总务部 automatic screwdriver电动启子
thickness gauge厚薄规
gauge(or jig)治具
power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车
forklift叉车 pallet栈板 glove(s)手套 glove(s) with
exposed fingers
割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指
little finger小指
band-aid创可贴 iudustrial alcohol工业酒精 alcohol
container沾湿台 head
of screwdriver起子头
sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱
garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器
lamp holder灯架 to mop the floor拖地 to
clean
the
floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机
packaging打包 missing part漏件wrong part错件 excessive defects过多的缺陷
critical defect极严重缺陷 major defect主要缺陷
minor defect次要缺陷 not
up
to
standard不合规
格
dimension/size is
a
little
bigger尺寸偏大(小)
cosmetic defect外观不良 slipped screwhead/slippery screw head 螺丝滑头 slipped screwhead/shippery screw thread 滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金
属)flash(塑件)毛
边
poor staking铆合不良
excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色 scratch划伤 poor processing 制程不良 poor
incoming
part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆
discoloration羿色
water spots水渍 polishing/surface processing表面处理 exposed
metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to
produce生产 equipment设备 to start a press开机
stop/switch off a press关机 classification整理
regulation整顿 cleanness清扫 conservation清洁
culture教养 qualified products, up-to-grade products良品 defective products,
not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱
die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模
packing material包材
basket蝴蝶竺 plastic basket胶筐
isolating plate baffle
plate;
barricade隔板 carton box纸箱 to
pull
and
stretch拉深 to put material in place, to cut material, to
input落料 to impose lines压线 to
compress,
compressing压缩 character die字模
to feed, feeding送料 transportation运输
(be)qualfied, up to grade合格 not up to grade,
not qualified不合格
material change, stock change材料变更 feature change
特性变更 evaluation评估 prepare for, make preparations for 准备
parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理
production unit生产单位 lots of
production生产
批量
steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over 切换 engineering, project difficulty 工程瓶颈
stage die工程模 automation自动化
to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for
stamping 冲压常词汇 stamping, press冲压 punch press,
dieing out press
冲床 uncoiler &
strainghtener整
平机
feeder送料机 rack,
shelf,
stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点
one stroke一行程 inch寸动 to continue, cont.连动
to grip(material)
吸料 location lump,
locating piece,
block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to
send
delinery back
to retrn of goods退货 registration登记
registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知 application form for purchase请购
单 consume,
consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模
to collect, to gather收集 failure, trouble故障
statistics统计 demand and supply需求
career card履历卡
to take apart a die卸下模具 to load a die装上模具
to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily
damaged
parts易损件 standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑 common vocabulary
for
die engineering 模具工程常用词汇 die 模具 figure file, chart file图档
cutting
die,
blanking die冲裁模
progressive die, follow (-on)die 连续模
compound die复合模
punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边
to bending折弯 to
pull,
to
stretch拉伸 Line streching, line pulling线拉伸 engraving, to
engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板 padding block垫块
stepping bar垫条 upper die base上模座
lower die base下模座
upper supporting blank上承板 upper padding
plate blank上垫
板
spare dies模具备品
spring 弹簧 bolt螺栓 document folder文件夹
file folder资料夹
to put file in order整理资料 spare tools
location手工备
品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人 equipment设备 waste materials废料
work in progress product在制品 casing =
containerazation
装箱 quantity of physical
invetory second count 复盘点数量 quantity
of
customs count 会计师盘,点数量 the first page第
一联 filed by
accounting department for
reference会计部
存查
end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list
will be sent to
accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and
physical
inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀
mold成型 material
for
engineering mold testing工程试模材料
not included in physical inventory不列入盘点 sample样品 incoming
material to be inspected进货待验
description品名 steel/rolled steel钢材 material
statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别
distribution department分发单位
location地点 chairman主席 present members出席人员 subject主题 conclusion结论 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked
by
/
prepared by
核准/审核/承办 PCE
assembly
production schedule sheet PCE组装厂生产排配表 model机锺 work order工令 revision版次 remark备注 production control confirmation生
产确认
checked by初审 approved by核准 department部门 stock
age
analysis sheet 库存货龄分析表 on-hand
inventory现有库存 available material良品可使用 obsolete material良品已呆滞
to be inspected or reworked 待验或重工 total合计 cause
description原因说明
part number/ P/N 料号 type形态 item/group/class类别 quality品质 prepared by制表 notes说明
year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量 physical count
quantity帐面数
量 difference quantity差异量 cause analysis原因分析
raw materials原料
materials物料 finished product成品 semi-finished product半成品 packing materials包材 good
product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓 spare parts physical
inventory list备品盘点清单 spare molds
location模具备
品仓
skid/pallet栈板 tox machine自铆机
wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线
cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模
expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝
form block折刀 stop pin定位销 round pierce
punch=die button
圆冲子
shape punch=die insert异形子 stock
locater
block定位块 under cut=scrap chopper清角
active plate活动板
baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块 club car高尔夫球车
capability能力 parameter参数 factor系数 phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高
速传递
heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄
咬
desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理
Anodize阳性处理 seal封孔 revision版次 part number/P/N料号
good products良品
scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条码 flow chart流程表单
assembly组装 stamping冲压 molding成型 spare parts=buffer备
品
coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶
sand blasting喷沙 grit 砂砾 derusting machine除锈机
degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕 shine亮班 splay 银纹 gas mark焦痕 delamination起
鳞
cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花
witness line证示线
patent专利 grit沙砾 granule=peuet=grain细粒
grit maker抽粒机 cushion缓冲 magnalium镁铝合金
magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗
blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin
formality滚针形
式
cam driver铡楔 shank摸柄 crank shaft曲柄轴
augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键
quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金 tungsten high
speed steel钨高
速的
moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机 模具工程类 plain die简易模
相关推荐：
loading