第一范文网 - 专业文章范例文档资料分享平台

Cisco 交换机综合实例

来源:用户分享 时间:2025/7/9 18:29:48 本文由loading 分享 下载这篇文档手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:xxxxxxx或QQ:xxxxxx 处理(尽可能给您提供完整文档),感谢您的支持与谅解。

Vlan 50 configuration successful

5509-ER-F1> (enable) set vlan 60 name Sales&Mktg Vlan 60 configuration successful

5509-ER-F1> (enable) set module name 1 Supervisor III Module name set.

5509-ER-F1> (enable) set port flowcontrol 1/1-2 send off Ports 1/1-2 flow control send administration status set to off (ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 1/1-2 receive off Ports 1/1-2 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 5509-ER-F1> (enable) set port negotiation 1/1-2 enable Ports 1/1-2 negotiation enabled

5509-ER-F1> (enable) set port name 1/1-2 GEC 802.1Q Trunk Ports 1/1-2 name set.

5509-ER-F1> (enable) set port channel 1/1-2 desirable Port(s) 1/1-2 channel mode set to desirable. 5509-ER-F1> (enable) set trunk 1/1 desirable dot1q Port(s) 1/1 trunk mode set to desirable. Port(s) 1/1 trunk type set to dot1q.

5509-ER-F1> (enable) set module name 3 RSM (RSM-ER-F1) Module name set.

5509-ER-F1> (enable) set module name 5 Fast Ether Uplinks Module name set.

5509-ER-F1> (enable) set port name 5/1-4 FEC ISL Trunk Ports 5/1-4 name set.

5509-ER-F1> (enable) set port speed 5/1-4 100 Ports 5/1-4 transmission speed set to 100Mbps. 5509-ER-F1> (enable) set port duplex 5/1-4 full Ports 5/1-4 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 5/1-4 send off Ports 5/1-4 flow control send administration status set to off (ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off Ports 5/1-4 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol) 5509-ER-F1> (enable) set port negotiation 5/1-4 enable Ports 5/1-4 negotiation enabled

5509-ER-F1> (enable) set port channel 5/1-4 desirable Port(s) 5/1-4 channel mode set to desirable. 5509-ER-F1> (enable) set trunk 5/1 desirable isl Port(s) 5/1 trunk mode set to desirable. Port(s) 5/1 trunk type set to isl.

5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts Module name set.

5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra Port 6/1 name set.

5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20 Ports 6/2-7 name set.

5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation Ports 6/8-12 name set.

5509-ER-F1> (enable) set port speed 6/1-12 100 Ports 6/1-12 transmission speed set to 100Mbps. 5509-ER-F1> (enable) set port duplex 6/1-12 full Ports 6/1-12 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired Ports 6/1-12 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired Ports 6/1-12 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 5509-ER-F1> (enable) set port channel 6/1-12 off Port(s) 6/1-12 channel mode set to off. 5509-ER-F1> (enable) set trunk 6/1-12 off Port(s) 6/1-12 trunk mode set to off.

5509-ER-F1> (enable) set spantree portfast 6/1-12 enable

Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution. Spantree ports 6/1-12 fast start enabled.

5509-ER-F1> (enable) set vlan 20 6/1-12 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports

---- ----------------------- 201/1-2 5/1-4 6/1-12

5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts Module name set.

5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC Ports 7/1-12 name set.

5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC Ports 7/13-48 name set.

5509-ER-F1> (enable) set port duplex 7/1-48 full Ports 7/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 7/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution. Spantree ports 7/1-48 fast start enabled. 5509-ER-F1> (enable) set vlan 10 7/1-12 VLAN 10 modified. VLAN 1 modified. VLAN Mod/Ports

---- ----------------------- 101/1-2 5/1-4 7/1-12

5509-ER-F1> (enable) set vlan 30 7/13-48 VLAN 30 modified. VLAN 1 modified. VLAN Mod/Ports

---- ----------------------- 301/1-2 5/1-4 7/13-48

5509-ER-F1> (enable) set module name 8 DevEng 10Mb Hosts Module name set.

5509-ER-F1> (enable) set port name 8/1-48 DevEng WinNT PC Ports 8/1-48 name set.

5509-ER-F1> (enable) set port duplex 8/1-48 full Ports 8/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 8/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution. Spantree ports 8/1-48 fast start enabled. 5509-ER-F1> (enable) set vlan 20 8/1-48 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports

---- ----------------------- 201/1-2 5/1-4 6/1-12 8/1-48

5509-ER-F1> (enable) set module name 9 DevEng 10Mb Hosts Module name set.

5509-ER-F1> (enable) set port name 9/1-48 DevEng WinNT PC Ports 9/1-48 name set.

5509-ER-F1> (enable) set port duplex 9/1-48 full Ports 9/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 9/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

搜索更多关于: Cisco 交换机综合实例 的文档
Cisco 交换机综合实例.doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印
本文链接:https://www.diyifanwen.net/c3ans48gk0q7f2vc1ug3g_2.html(转载请注明文章来源)
热门推荐
Copyright © 2012-2023 第一范文网 版权所有 免责声明 | 联系我们
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ:xxxxxx 邮箱:xxxxxx@qq.com
渝ICP备2023013149号
Top