RJ45 Modular Jack Connectors with Pulse TransformersTM11RD - 5TANA Series
Pulse Transformer Circuit DiagramInsulated transformerChoke coilTD+ 1CT 3TX- 2RD+ 7CT 6RD- 8 4GRAND 51 TX+2 TX-3 RX+456 RX-78RJ11 (6 position) plug insertion preventionBuilt-in optical indicators*Light colors are determined by the color of LED's used.CircuitRJ45Outline of mating plugIncorrect Plug Insertion Prevention Key Light pipe1
PCB■Features1.Pulse Transformers Support FastEthernetEquipped with built-in insulation transformers andcommon mode choke coils, withstanding voltage of 1.5kV and supporting 100Base-Tx and 10Base-T.2.Incorrect Plug Insertion Prevention KeyA built-in key offers protection against insertion of 6-conductor type modular plug.3.Built-in optical indicatorsOptical indicators are integral part of the connectors,saving space on the board.There is no emission of any electrical noise.4.EMI protectionMetal shield covers the outer surfaces of the connectorsassuring complete protection against electromagneticinterference.5.FCC standardsMeets requirements of FCC Title 47, Part 68, Subpart F.
6.Environmental considerations
Plating compounds are lead-free.
■Applications
Notebook PC's, telecommunication hubs, routers, bridgesand ATM transmission equipment, Ethernet switches andnetworking equipment, office equipment, test andmeasurement equipment.
■Product Specifications
RatingsVoltage rating 125V ACItem1.Insertion resistance2.Insulation resistance3.Withstanding voltagePulse transformer4.Insertion resistance5.Return loss6.Inductance7.Cross talk(Reference)8.Common mode rejection ratio(Reference)Specification-2dB min.100M ohms min.No flashover or insulation breakdown.-1dB min.-20 dB max.-16 dB max.-12 dB max.-10 dB max.350μH min.-40 dB max.-35 dB max.-30 dB max.-30 dB max.-20 dB max.Operating temperature range: -25?to +80?(Note)Conditions1 to 65MHz100V DCBasic terminal between 123-45-768500V AC / one minutePrimary (RJ45 side) to secondary (PCB side)1500V AC / one minuteTerminal to shield1500V AC / one minute1 to 65MHz1 to 10 MHz10 to 30 MHz30 to 60 MHz60 to 80 MHz0.1V, 100KHz, 8mADC1 to 30 MHz30 to 60 MHz60 to 100 MHz1 to 50 MHz50 to 150 MHzConnectorNote: Includes temperature rise caused by current flow.■MaterialsComponentInsulatorContactsShieldIncorrect insertion prevention keyPulse transformer Optical pipeMaterialPBTCopper alloyCopper alloyStainless----------Polycarbonate----------ClearUL94V--0Finish/ColorBlackContact area: Gold platedTermination area: Tin platedTin platedRemarksUL94V-0■Ordering information1Series name2Connector type3Direction of locking lever45678910(mating plug)Jack suffix numberTransformerTransformer typeIncorrect insertion prevention keyJack opening codeNumber of inserted contactsOptical pipe: TM11R: Jack D: Down: 5T: With transformer A: Transformer circuit typeNA-A: With built-in key8: 8 contacts8: 8 contactsLP: With optical pipe insertedBlank: Without optical pipeTM11 R D - 5 T A NA - A - 8 8 - LP123456789102
■Modular Jack Connectors (With built-in optical pipe)
Contact No.116Contact No.8 21.313.6Contact No.115.7517.5Contact No.80.4810.80.324.2Part NumberTM11RD-5TANA-A-88-LPCL No.CL222-2936-3RoHSYES4Suggested dimensions of LEDs
LED light emitting centerPrinted board edge?3.25BRecommended PCB mounting pattern
20.75MINNo conductive traces11.4310.75MAX7.42.7MAX753186423.2MAX1.61.5MAX12.76.2?1.638-?0.95.55MIN3.052.541.278.8911.615.75LED center position5BPulse Transformer Circuit Diagram
TD+1CTTD-Board side32
1CT:1CT2TX-3RX+
Cable side1TX+
RD+7CT
6
1CT:1CT75?0.001μF75?75?75?RD-86RX-4578
4
CHS GROUND5
●Precautions
1234567
Hirose Electric did not check the compatibility with the PHY chip. When replacing other manufacturers jack it is recommended to verify thecompatibility with the actual equipment. This connector is mounted on the board using wave or manual soldering. Do not use reflow soldering.Recommended board thickness: 1.6mmTo assure correct operation of the indicator light pipes LED's must be installed directly on the PCB, within recommended dimensions and with light emittingcenter in upward direction.Mount the LED so that the center of the light emitting center aligns with the center point as dimensioned on the Recommended PCB mounting pattern above. Verify the actual LED's mounting pattern with it's manufacturer, then add it to the PCB mounting pattern, assuring the correct placement of the center point.IPA cleaning at room temperature is recommended for the cleaning of this product.When an aqueous cleaning agent is to be used, there is a concern that the light pipe (made of polycarbonate resin) may change color; therefore, pleasemake a selection based on a table showing the effects on the resin.These tables are issued by the various manufacturers of cleaning agents.3.183.563
Modular Jack Connectors (Without built-in optical pipe)
Contact No.116Contact No.821.36.3861615...133Contact No.1Contact No.80.4810.80.315.7517.5Part NumberCL No.RoHSTM11RD-5TANA-A-88CL222-2932-2YESRecommended PCB mounting pattern
20.75MIN11.43No conductive traces10.75MAXPrinted board edge4?3.25.72.675318642?1.6354NI5.M08-?0.9.1.272535.8.89515.75Pulse Transformer Circuit Diagram
TD+11TX+
CT3TD-2
1CT:1CT2TX-edisRD+73RX+
edis derCT
6
laboaBCRD-81CT:1CT6RX-75?75?75?44
50.001μF5
75?78
Hirose Electric did not check the compatibility with the PHY chip. When replacing other manufacturers jacks it isrecommended to verify the compatibility with the actual equipment.
This connector is mounted on the board using wave or manual soldering.Do not use reflow soldering.Recommended board thickness: 1.6mm
IPA cleaning at room temperature is recommended for the cleaning of this product.
When an aqueous cleaning agent is to be used, there is a concern that the light pipe (made of polycarbonate resin) maychange color; therefore, please make a selection based on a table showing the effects on the resin.These tables areissued by the various manufacturers of cleaning agents.
4
■BBCHS GROUND●Precautions
1234
■Technical Data
Measurement results of electrical characteristics
●Insertion Loss
Insertion Loss
Network analyzer
MHz00
10
20
30
40
50
60
70
80
-0.2-0.4-0.6Bd-0.8-1-1.2-1.4-1.6Pulse transformer section-1.8-2
Reflection Loss
Reflection
Network analyzer
MHz00
10
20
30
40
50
60
70
80
-10-20Bd-30-40-50-60-70
Pulse transformer section-80
Crosstalk (Reference)
Cross Talk
MHzNetwork analyzer
00
10
20
30
40
5060
70
80
90
100
-10-20-30Bd-40-50-60-70
Pulse transformer section-80
-90-100
Common Mode Rejection Ratio (Reference Value)CMRR
Network analyzer
MHz
0010
2030405060708090100110120130140150
-10-20B-30d-40-50-60
Pulse transformer section-70-80
●●●5
相关推荐：
loading