g.the height of text文本的高度:
the annotations district: 3.0mm for title; 2.5mm for content附注区：题头3.0mm；内容2.5mm；
the header area: 3.0mm for drawing number; 2.5mm for scale, version, date, etc; 2.0mm for the rest, 0.15mm for the typing line width; Letter should be clear when printing half.图标区：图号3.0mm；比例、版本、日期等信息2.5mm；其余2.0mm 打印线宽应为0.15毫米；当图纸缩半打印时，文字应清晰可见。
h.General, apply small font to piece mark assembled in shop, and apply big font to all texts.车间内装配用的零件标号通常采用小字体，大写字体通常用于所有文本。 i.Member title with double underline spaces the first underline 1mm and spaces the second underline 2mm; 0.3mm for the first underline thickness, 0.13mm for the last.构件名称必须带双下划线，离第一条下划线1mm；第一条下划线粗0.3mm，第二条下划线0.13mm，二者间距1mm；
j.Section must be with single heavy underline, 0.3mm for the thickness, 1mm for the clearance of word line.剖面必须带单条粗下划线，线粗0.3mm,字线间距1mm.
3.5 Size Dimension尺寸标注
a. Indicate altitude with meter and millimeter for other size. Do not show unit in drawings.除高程以米计以外其余尺寸以毫米记，图中不标注单位。
b. Provide arrow dimension at the end of size. Space at least 1mm between dimension line and dimensioning position.尺寸端部统一规定采用箭头标注，尺寸线与标注部位至少预留1mm的间隙
c. Dimension should be layered. The first layer is member locating point dimension, the second layer is member length and the third layer is locating of local detail on members, the fourth layer is dimensioning of local detail. Dimension line should avoid cross.尺寸要分层标注，第一层尺寸为构件定位点尺寸，第二层为构件长度，第三层为局部细节在构件上的定位，第四层为局部细节的尺寸标注。尺寸线应尽量避免交叉。
d. Dimension in the same series should be aligned in line.同一系列的尺寸应
整列对齐。 e. In principle, the arrow at the end of dimension line is 1.5mm(general drawing) or 1.2mm (detail drawing).尺寸线端部的箭头原则上为1.5mm(一般图)或1.2mm(详图) f. Dimension Splice position and eccentricity size as follows:节点板位臵以及偏心尺寸按下图要领标注
g. Dimension detail size as follows(n is greater than or equal to 3):细部
5
尺寸按下列要领标注。(n要大于等于3)
h. Azimuth and the direction of diagrammatic presentation方位以及图示方
向
3.6 Drawing Number图纸编号
a. See building project drawing number system as follows. Drawing number consists of drawing title, category code name and serial number.建筑工程图纸编号系统(见下表) 图纸编号由图纸名称、种类代号加节号（一部分为层号）以及序号构成。
6
Drawing Name Drawing No. Remark 图纸名称 图纸编号 备注 Layout of bolt at toe A+code number Detail is contained. 柱底螺栓布臵图 Ａ+序号 含详图 Plan F+floor Layout of prepared hole and 平面图 mark+code numberembedded parts is contained. Ｆ+楼层号+序号 含预留孔布臵图、预埋件布臵图 Elevation E+truss 立面图 name+code number桁架名参阅附图 Ｅ+桁架名+序号 Joint standard drawingTS+code number 节点标准图 TS+序号 Weld standard drawing TWS+ code number 焊接标准图／坡口标准图 TWS+序号 lifting standard drawingTKS+ code number 吊装标准图 TKS+序号 elevator steel structure standard drawing TEV+机号+序号 电梯钢结构标准图 curtain wall steel structure standard TCW+floor mark+ drawing code number 幕墙钢结构标准图 TCW+楼层号+序号 ALC steel structure ALC+floor mark+ standard drawing code number ALC钢结构标准图 ALC+楼层号+序号 stairs steel structure TKF+stairs name+ standard drawing楼梯钢code number 结构标准图 TKF+楼梯名+序号 application, TPS+floor mark+ galvanizing standard code number drawing涂装、镀锌标准图 TPS+楼层号+序号 Detail of main truss column head or other section+C+ code column head主桁架柱头以number 及其他柱头详图 节+C+序号 Detail of main truss inclined piece(vertical section+T+ code 分类方法参阅附图 plane) number 主桁架斜杆（垂直面）详图 节+T+序号 Detail of main truss floor+G+code horizontal member number 7
楼层号+G+序号 floor mark+B+ All kinds of trabecula is Detail of beam code number contained. 梁详图 楼层号+B+序号 含各类小梁 Detail of interlaminar floor mark+P+ 楼层号以柱头所在的楼层为准 column code number 层间柱详图 楼层号+P+序号 floor mark+EMB+ Detail of embedded partscode number 预埋件详图 楼层号+EMB+序号 Detail of horizontal floor mark+H+ inclined piece code number 水平小斜撑详图 楼层号+H+序号 Detail of vertical floor mark+V+ 楼层号以柱头所在的楼层为准 inclined piece code number 垂直小斜撑详图 楼层号+V+序号 N+steel casting Steel casting mark+ code number 铸钢件 N+铸钢件号+序号 K+stairs mark+ Stairs code number 楼梯 K+楼梯号+序号 b.Shop Drawing Numbering System桥梁工程图纸编号系统（见下表） PrefixContents Description内容描述 前缀 WD Welding Detail 焊接详图或标准图 Work Sheets(calculation and layouts used to prepare shop drawings; not WS to be reviewed as shop fabrication )工作表（用于准备加工图的计算书和方案图；不需要送审） Typical details and layouts(details and layouts to prepare shop drawings; TD not to be reviewed as shop fabrication drawings)典型详图和方案图（用于准备加工图的详图和方案，不需要送审） General shop notes and typical details(lists appropriate notes for GN welding, paint, etc.) 车间制造的注解和典型详图（对焊接、涂装等列举一些适当的注释） Basic girder diagrams ( Web and flange cutting diagrams)基本大梁图（腹BG 板和翼缘切割图） Web camber details ( camber cutting and splicing of webs)腹板预拱度详WC 图（预拱度切割位臵和腹板拼接） Flange splicing details( assembly and splicing of flanges).翼缘板拼接FS 详图（翼缘板装配和拼接）。WC或BG图应包含腹板至翼缘的焊接 Field work sheets ( used to obtain field dimensions and/or show required FW fieldwork, including field reaming and drilling) 现场工作表（用于标主桁架水平杆件详图 8
相关推荐：
loading