钢结构详图设计标准

示工地工作的相关尺寸和/或工地铰孔和钻孔等工作） Horizontal curve diagrams ( final line curve diagrams per piece with HC horizontal ordinates shown)水平曲线标注方法（标注每段曲线在水平线上的最终横、纵坐标） Girder job standards( parts details for I girders, box girders and tub X girders)主梁零件标准图（工字梁、箱梁和槽式梁的零件详图） Stringer job standards纵梁零件标准图 Z Miscellaneous job standards(parts details, rolled beams, cross frames, M diaphragms, etc.) 杂项零件标准图（零件详图、轧制小梁、横梁结构、横隔板等） Sub-assemblies(Parts, shop or field assembled, as units prior to SB or SD incorporating into a shipping piece or the structure)组件（将多个零件在工厂或现场拼装成的船运部件或结构件） Anchor bolt plans, field bolt and erection framing plans (location of shipping piece marks). Note: these are not erection procedure plans.E 锚固螺栓平面布臵图，现场安装螺栓平面图和结构安装图（带标记的船运部件位臵），说明：这些不是安装工艺图 Shop assembly diagrams(line assembly reaming, unit assembly, etc.工厂SA 拼装图（画出装配的铰孔，装配的组件等） Details of girders, cross frames, stringers, diaphragms, etc. 梁，横1 thru… 梁结构，纵梁，横隔板等的详图 Shipping procedures(detailed procedure to ship unique pieces)船运工艺SP （特殊构件的详细船运工艺） Welding procedures( used to show required welding procedures; to be WP submitted and approved separately from shop detail drawings)焊接工艺（用来明确焊接工艺的要求；应分别根据车间详图提交审核） Note: Prefix typically followed by numerical identification 1,2,3,etc. 注释：前缀通常是通过数值诸如1，2，3来确定。 Shop Detail Drawing Numbering Sequence 桥梁工程加工图编号顺序

There should be a logical sequence in shop detail drawings that will aid the reviewer and shop personnel. The approval review process will be expedited if all structure drawings are organized in a common sequence. The prefixed drawings should be located within sets in the order shown in shop drawing numbering system.

加工图应遵循逻辑的编号顺序，以便为审图者和生产人员服务。如果所有的结构图按常用的顺序整理完整，审图过程就可以加快。图纸的前缀应根据前面的图纸编号系统里的相关条目进行设臵。

Numbered drawings should be sequenced similarly to the following example: 已编号的图纸顺序应和下表类似： Description Drawing No. 描述 图号 Bearing Detail支座详图 1 Girders梁 2G1A 2AC，2BC，2C* 3G2A 3 4G3A 4 9

5G4A 6G1B 7G2B 8G3B 9G4B 5 6 7 8 9 Cross Frames, Diaphragms&other Misc. 10 横梁结构，横隔板以及其它杂项 3.7 Marking System for Shipping Pieces桥梁工程构件编号系统 Identifier名称 G BG TG S D CF，K，X L or LB MS DU AB BP BR EB FB or B PP LP MP P RP SP W WD Description描述 Girder大梁（用于翼缘、腹板的构件） Box Girder钢箱梁（封闭的箱形构件） Tub Girder平梁（敞开的箱形构件） Stringer纵梁（型钢构件） Diaphragm横隔板（介于主要构件或板块间的单个滚压形式） Cross Frame剪刀撑（介于主要构件之间的组合构件，这些构件主要为宽翼缘截面，角钢等） Lateral Bracing横向支撑（所有水平面，对角支撑） Miscellaneous杂项（无法归类的船运散件） Deck Units桥面单元（通常指铁路桥上附带钢板的平面梁） Anchor Bolt锚固螺栓 Bronze Plate铜板 Brackets牛腿（悬臂形式） Elastomeric Bearing弹性支座 Floor Beams平面梁（扎制型钢或焊接工字梁） Preformed Pad预制垫 Leveling Plate水平测量用钢板 Masonry Plate砌筑板 Pin销 Rocker Plate平衡板 Sole Plate基础板 Washer垫圈 Weld Detail Drawing焊接详图（用在有许多焊接详图的复杂结构） Fracture critical pieces may be prefixed ?F?, such as FG, FBG, FTG, etc. This is optional and may be used by a Fabricator to differentiate this material. The above letters may be prefixed with the sheet number on which the piece is detailed, serving as a self-indexing system, and suffixed with a numerical identification. Longitudinal main members shall be suffixed A, B, C, etc. in addition to their numerical suffix. 临界脆断构件可以加前缀“F”，诸如FG，FBG，FTG等等。这是可选择的，可以由制造商自己采用以辨别这种材料。以上字母可以根据图表编号加前缀，也能根据数值的辨别加后缀。纵向的主构件，除了它们的数值后缀外，还可以加后缀A，B，C等。

*Use letters as suffix when details require more than one drawing. *当详图需要不止一张时，用字母作为后缀。

Note: Certain projects may require deviation from the Shop Detail Drawing Numbering

10

System Sequence, dependent upon the Fabricator?s requirements. Also, WS, TD, GN, WC&FS drawings may be prepared and submitted [with other necessary sheets/information (E&WP)] prior to balance of detail drawings on large projects in order to begin with fabrication of these pieces. Partial submittals must be complete enough to allow checkers to adequately cross-reference information and avoid requiring later re-checking.

注释：具体项目也可能根据制造商的需要进行调整使加工图编号系统，这样顺序有可能产生偏差。同时，在一些大的项目中，为了在一开始就方便零件的装配，要先准备和提交WS，TD，GN，WC和FS图纸 [连同其它必要的图纸/信息（E和WP）]，目的是及时完成以上图表以便让复核人员能充分地相互对照，避免事后再次检查。

3.8 Building Project Member Numbering System建筑工程构件编号系统

Number member according to follow principle, the category code name of member is the same to drawing numbering.构件根据以下原则编号，构件的种类代号采用与图纸编号相同的种类代号。 １）main column主要柱

section number+C+elevation number+serial number节号+C+立面号+序号

２）main horizontal member of truss主要桁架水平杆件

section number+G+elevation number+serial number节号+G+立面号+序号 ３）main horizontal member of truss主桁架水平杆件

floor number+G+elevation number+serial number楼层号+G+立面号+序号 4）beam, interlaminar beam梁、层间梁

floor number+B+design mark+serial number楼层号+B+设计记号+序号

M+floor number+B+design mark+serial number M+楼层号+B+设计记号+序号 5）interlaminar column层间柱

floor number+P+design mark+serial number楼层号+P+设计号+序号 6）horizontal inclined brace水平小斜撑

floor number+H+design mark+serial number楼层号+H+设计号+序号 7）vertical inclined brace垂直小斜撑

floor number+V+design mark+serial number楼层号+V+设计号+序号 8）embedded parts预埋件

floor number+EMB+serial number楼层号+EMB+序号 3.9 Plan建筑工程平面图

It contains axis, member, member mark, bill of material(member mark, sectional dimension, material, node number), the end of shop, field splice, bracket length, plane brace, elevation brace(dashed line)and direction, direction of assembly, elevator, stairwell, curtain wall, part section, note.内容包括轴线、构件、构件号、材料表（构件号、截面尺寸、材质、节点号）、工厂端点、工地拼节点、牛腿长度、平面支撑、立面支撑（虚线表示）及方向、安装方向、电梯、楼梯井、幕墙、局部剖面、注记。 3.10 Elevation建筑工程立面图

It contains axis, member, member mark, bill of material(member mark, sectional dimension, material, node number), the end of shop, field splice, bracket length, elevation brace, etc.内容包括轴线、构件、构件号、材料表（构件号、截面尺寸、材质、节点号）、工厂端点、工地拼节点、牛腿长度、立面支撑等。 3.11 Detail建筑工程节点图

11

It contains node number, node detail drawing, specification of gusset plate, specification of bolt and quantity, bolt length. It contains lifting ear, lifting hole, concrete press-in hole, steam hole.内容包括节点号、节点大样图、节点板规格、螺栓规格及数量、螺栓长度。要领包括吊装耳板、吊孔、砼压入孔、蒸气孔。 3.12 Standard Abbreviation 标准缩写 See annexed table 3.见附表3

第四章Standard of Model Building X-STEEL建模标准

4.1 Set of Parameter参数设臵

4.1.1 Server服务器 Use correct server name if multiple user.如果是多用户，使用正确的服务器名称。

4.1.2 Autosave自动存盘 Modify the path of autosave to user?s list. Transfer the

title of autosave to title district.修改自动存盘路径到用户的目录下。并将自动存盘图标调到图标栏中，set XS_AUTOSAVE_DIRECTORY=%XS_RUNPATH%\\autosave\\ , The set is very effective when users are many and model is big.当用户比较多，模型比较大的时候，此设臵非常管用。

4.1.3 Clearance between gusset plate and beam节点板与梁的间隙 REM SET XS_ALLOW_SHEAR_PLATE_CLASH_FLANGE=TRUE，remove REM去掉REM 4.２ Set of Bolt Symbol and Material Symbol螺栓符号、材质符号设臵

Bolt mark螺栓记号 Show bolt as follows according to its diameter:螺栓根据直径的不同，以下表记号表示

Name名 称 Mark记 号 M16 M20 M22 M24 Show material mark as follows:材质记号如下表所示

Name名 称 Mark记 号 A36 A500 GR.B A572 GR.50 A572 GR.65 A913 GR.65 A992 4.３ Set of Shortcut Key快捷键设臵 See annexed table 4见附表4

4.４ State Numbering状态编号 Number classification according to section number and member type. It is established by special person.根据节号、构件类型来分类编号，由专人负责建立

4.５ Unit and Decimal System单位和十进制设臵 Length should be two decimal fraction when its unit is millimeter. Angle should be three decimal fraction.当长度单位为毫米时，长度尽量要设臵为两位小数，角度要设臵为三位小数。 4.６ Piece Numbering零件编号

section number+sectional material code name+serial number节号+型材代号+序列号码 sectional material code name型材代号：plates板材—P

W structural section W型钢—W pipe圆管—PP steel angle角钢—L bar钢筋—B

12