数通高培实验指导书ISSUE 1.0

来源：用户分享时间：2025/7/28 18:09:36 本文由

说明：文章内容仅供预览，部分内容可能不全，需要完整文档或者需要复制内容，请下载word后使用。下载word有问题请添加微信号:xxxxxxx或QQ：xxxxxx 处理（尽可能给您提供完整文档），感谢您的支持与谅解。

数通高培工程师实验指导书ISSUE1.0

学员用书

0 errors, 6596240 CRC, 0 giants Output:390 packets, 7324 bytes, 0 underruns 0 MulticastPkts, 0 MulticastBytes 0 CRC, 0 aborted sequences, 0 giants

[router-B]display pos interface pos5/0/0:1 Pos5/0/0:1 current state: up Line protocol current state: up Physical layer is Packet over SDH Card info: POS OC-48/STM-16-SM-SR-LC

Line Type: SingleMode, WaveLength: 1310nm, Transmission Distance: 2km

Average Optical Output Power: -10~-3 (dBm) Receiver Overload: -3 (dBm)

Optical Center Wavelength: 1310 (nm) Receiver Sensitivity: -18(dBm)

Description: HUAWEI, Quidway Series, Pos5/0/0:1 Interface Internet address is 1.1.1.2/24 Is-Primary

The Maximum Transmit Unit is 4470 bytes, the BandWidth is 155000 Kbps Loopback not set, Clock source master, Scramble enabled, Urpf disabled Link-protocol is PPP

MRU: 4470 bytes, Negotiate Timeout set 3 seconds Peer MRU: 4470 bytes, Magic number: 83911574 Peer IP address is 1.1.1.1/32 LCP: Opened

NCP: IPCP Opened, MPLSCP Opened

Input: 336 Lcps, 42 Ipcps, 3 Mplscps, 0 Osicps, 40 Invalids Output:430 Lcps, 2 Ipcps, 2 Mplscps, 0 Osicps, 0 Invalids

数通高培工程师实验指导书ISSUE1.0

学员用书

Hold time is 10 (sec)

Input: 323 Timerhold Packets Output:322 Timerhold Packets Statistics last cleared: never Traffic statistics:

Last 5 minutes input rate 3 bytes/sec, 0 packets/sec Last 5 minutes output rate 3 bytes/sec, 0 packets/sec Input: 6596631 packets, 277105069 bytes 0 MulticastPkts, 0 MulticastBytes 0 errors, 6596240 CRC, 0 giants Output:444 packets, 8188 bytes, 0 underruns 0 MulticastPkts, 0 MulticastBytes 0 CRC, 0 aborted sequences, 0 giants

SECTION: Seconds Count

B1 0 0 LOS 0 0 OK LOF 0 0 OK OOF 0 0 OK SES 0 0

SSEFS 0 LINE:

B2 0 0 LREI 0 0 OK LRDI 0 0 OK LAIS 0 0 OK SFBERR 0 0 OK SDBERR 0 0 OK

数通高培工程师实验指导书ISSUE1.0

学员用书

LES 0 LSES 0 LUAS 0 LFEES 0 LFESES 0 LFEUAS 0 PATH:

B3 0 0 PREI 0 0 OK PLOP 0 0 OK PAIS 0 0 OK PRDI 0 0 OK PPLM 0 0 OK PES 0 PSES 0 PUAS 0 PFEES 0 PFESES 0 PFEUAS 0 CLOCK RECOVERY: RDOOL OK RROOL OK TROOL OK Rxd: 0 packets

0 FCS, 0 aborts, 0 Max, 0 Min Txd: 0 packets

0 underruns, 0 aborts SDH overhead:(Rx/Tx)

F1 : NA/NA , J0 : 0x4e/0x4e, K1 : 0x00/0x00, K2 : 0x00/0x00

数通高培工程师实验指导书ISSUE1.0

学员用书

S1 : 0x08/0x08, C2 : 0x16/0x16, F2 : NA/NA , Z3 : NA/NA Z4 : NA/NA , V5 : NA/NA

Received section trace(J0): \

4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Received path trace(J1): \

4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Transmitted section trace(J0): \

4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Transmitted path trace(J1): \

4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine 3、需要进行ppp验证请参照POS接口的ppp验证配置

2.5 E1/CE1接口的配置实验环境： POS?ó?ú????1.1.1.0/24A.1.2B CPOS接口配置上机组网图（1）、路由器A和路由器B采用E1接口进行互连 1、进入E1接口(控制口)，配置相关物理参数 RouterA物理层的参数采用缺省参数：设置E1接口的线路编解码格式：code hdb3 设置E1接口的时钟模式：clock master 设置E1接口的环回方式：undo loopback 激活E1/CE1通道：using e1 RouterB物理层的参数配置：

搜索更多关于：数通高培实验指导书ISSUE 1.0 的文档

数通高培实验指导书ISSUE 1.0.doc 将本文的Word文档下载到电脑，方便复制、编辑、收藏和打印

下载这篇word文档

本文链接：https://www.diyifanwen.net/c88k6t36k61371qz5cnlr_8.html（转载请注明文章来源）