QEI-7.5-007-F002 手机质量检验记录

Handset inspection record手机质量检验记录

Lot No.数量： Model型号： Sample Level 抽样水平： Sample Qty: 抽检数量：

Inspection Item 检查项目: PCBA ICT Test PCBA在线测试

Requirements 技术要求 a) To check if there’s short, open of the solder happened; 确认PCBA上无焊锡的短路，开路发生； b) To check if the value of all the components in under the SPEC; 确认元器件的值都在规格范围内； c) To check if the electrical performance (especially the IC) is OK. 确认电路板的电气性能（主要为IC）OK RF Test 射频测试 a) Measure TXDATE AC peak voltage(European band) between 300 and 540 mV; 确认TXDATE AC 高峰电压值(European band)在300到540之间。 b) To check RSSI adjust(-42dbm) is between 1 and 230d 确认-42dbm下接受灵敏度在1到230d之间。 c) To check RSSI adjust(-84dbm) is between 1 and 230d 确认-84dbm下接受灵敏度在1到230d之间。 d) To check measure modulation depth(European ch9)(slot9) between 202 and 403khertz 确认调制频率(European ch9)(slot9)在202和403khertz之间 e) Measure NTP level (south America ch0)(slot0) is between 20and 26dbm 确认传输功率(south America ch0)(slot0)在20和26dbm之间 OBA Cosmetic Inspection 出货外观检查 a) To check if the maximum gap between screen and plastic parts is 0.5mm. 确认屏幕和塑料部件的间隙不得大于0.5mm.. S-3

AQL质量接受限:

Critical 重缺陷： Minor 小缺陷：

2.5

4.0

Result 结果 b) To check the surface of phone, there’s no scratch, dirty, impact etc. 确认手机的表面无划伤，污，碰撞等不良 c) To check the printing number on the keypad should at the center of the keypad and size of printing number should be the same size. 检查按键上字幕的位置应该在按键的中心位置，而且字母大小应一致 d) To check the dirty dot on the LCD lens should smaller than 0.05m2 on the condition of 30cm distance. 30cm 足够强度灯光下，检查LCD 显示区域污点大小应该小于0.05平方毫米。 e) To check the space between front shell and rear shell is according the spec. 检查确认手机上下壳间隙在规格内 f) To check the scratch nick is shorter than 4mm and width is narrower than0.2 mm (include front, rear shell and battery cover). 检查确认手机壳子包括电池盖上的划痕长度不能超过4毫米，宽度不能超过0.2mm. OBA Functional Test 出货功能测试 a) To test the numeric key, check if the LCD shows the number consists with the key marking. 依次测试数字键,确认LCD显示数字是否与按键标示数字相同。 b) To test the programmable key, check if the LCD showing is consisting with the key marking. 依次测试编程键,确认LCD显示是否与按键标示相同. the key marking. 依次测试字母键,确认LCD显示是否与按键所要求内容相符。 d) Dial 100 on the handset listen music from the reference phone, then dial 102 on reference phone, listen human voice from handset, verify that there is not voice modulation and noise. 拨100，听参考机中的音乐，然后用参考机拨102，听话机中的人声,检查声音没有波动，且没有杂音为OK. e) Push all buttons on handset, each pressure should cause a \按手机上的每个按键，确认每一次按键都能听到哔的声音 c)c) To test the alphabetic keys, check if the LCD shows the display complied with Power supply 充电器 Battery 电池 N/A N/A

商检批号:

生产日期: _

判定结果: _____________

认可检验员: ___________

QEI-7.5-007-F002