钻 井 英 语 常 用 语
1. Mix 800 BBLS spud mud 配800桶开钻泥浆
2. Hold a spud safety meeting w/crew prior to DRLG 22＂Hole 钻22＂井眼之前，开个安全会
3. How many bits are there on the rig-floor? 钻台上有多少个钻头
4. There are two bits on the rig-floor, one is tri-cone bit, the other is a PDC bit. 有两个钻头,一个是三牙轮,一个是PDC钻头
5. Sweep hole w/100 BBL HVP while you drilled to casing setting point 钻达下套管深度时用100桶高粘清扫井眼
6. Take a Totco survey if any bit trip ,take a wireline survey if lost circulation occurs otherwise , Drop ToTco. 一旦起钻投测，若井漏，吊测，否测投测。
7. Spot 250 BBLS HVP on Bottom .Drop Totco, slug pipe ,pull out of hole (POOH). 封底250桶高垢投测，重浆压钻杆起钻 8. Run casing into hole. 下套管
9. Pooh for 185/8＂CSG ＆ lay down 22＂BHA.
起钻下18-5/8”套管，甩掉22”钻具组合。 10. Circulation bottoms –up
循环一周
11. Mix/pump 400 sacks דG” cement , Dropped plug .Displace w/wtr ,Bumped plug to 1000psi ,check the float ok
混合并打入400袋G级水泥，投塞子，碰压到1000psi.
12. Do you perform cement top job ?
打水泥帽了吗？
13. Center the casing ,weld brace ＆ casing supports, please .Then make up .Flowline ＆ fill up line ,CUT csg(casing) below RT(rotary table). 把套管居中，焊套管支撑，焊出水口和灌浆管线,把转盘底下的多余套管割掉。
14. P/u（pick up） ＆ N/u (nipple up)16＂BHA ＆ into hole) to toc(top of cement) , hydro test 组合16＂BHA 然后下钻，静液观察． 15. Do you make maintenance work regular? 你经常做设备保养工作吗？ 16. What did you do this morning ? 今天早上干了什么？
We clanged the liner ＆ piston of mud pump 2＂. 我们换了２#泵的缸套和活塞
17. It is time for cutting ＆ slipping drlg(drilling) line 该割大绳了
18. Please don’t put too many things on the rigfloor 不要把杂乱东西放在钻台上 19. What is the operation now? 现在在干什么？
20. Could you tell me the operation today? 你能告诉我今天在干什么吗？ 21. Work Safely! Good luck! 工作时注意安全，祝你好运． 22. Make a wiper trip to the csg shoe
短起下至套管鞋。
23. How many stands set on the rig floor?
RIH(run 钻台上立了多少立柱？
24. Nipple up BOP(blow out preventer) stack. 安装封井器
25. Describe your BOP configuration, please. 讲一下你们的封井器组合
26. PT BOPE(blow out preventer equipment) ＆ related equipment as per SA requirements . 按阿美公司的要求对封井器及相关设备进行试压 27. Do you print the drilling chart ? 你打出钻时曲线了吗？ 28. Wake me up @ 5:00. 5：00叫醒我。
29. P/u (pick up)BOP set csg slip .
提起封井器，坐套管卡瓦。
30. P/u BOP , rough cut csg , dress ＆ bevel csg stub to 4
1
/2＂, N/u CIW casing head testing spool PT same to 5000psl . 上提封井器，粗割套管，打磨平套管并留够4-1/2”长，安装CIW套管头,并试压5000psi.
31. What size of jet will be used ? 用多大的水眼
32. What method do you take to raise the drilling speed . 哪种方法能提高钻井速度。
To increase weight on bit is the effective method 增加钻压是最有效的方法
33. The driller was working on DP(drill pipe) while we repaired the pump. 当修泵时，司钻要不停地活动钻具 34. The valu
35. The valve seat was washed out , please get the puller.
凡尔座刺了，请把启拔器拿来。 36. Please recheck the packing box. 请再检查盘根盒
37. Make up steerable assy(assembly) ＆ RIH. 组合定向井钻具，然后下钻
38. Flow check connection ,always be prepared for a flow ＆ H2S gas. IF there is a flow ,record depth if there is “no” H2S Cont DRLG w/wtr ＆ gel sweeps . 检查溢流，时刻做好溢流和出H2S气体的准备，如果有溢流，纪录井深。如无溢流，继续钻进。
39. At liner point, pump 75 BBL HVP “marker” sweep followed by 84 PCF mud to surface circulation hole clean. 钻达下尾管深度，打入75桶高粘泥浆，然后使用比重为84PCF的泥浆循环至地面清扫井眼。
40. Record total pumps stks(strokes). 记录泵冲
40、Fill pipe w/mud every 10 stands.
下钻时每10柱灌一次泥浆。
41、RIH liner on 5” DP, Drop a 4”Drift Down each stands, use only “one” Drift.
使用1只4”通径规通钻杆，并用5”钻杆下入尾管。 42、N/U & set 11” test plug.
安装11”试压塞准备试压。
43、Flush through BOP stack choke manifold w/water
使用清水冲洗封井器和节流管汇。
44、PT（pressure test）Hydril (300/2000PSI 10 minutes each
w/chart)
对海德里尔封井器试压（低压300psi/高压2000psi） 45、P/U 9-5/8” cup tester set 60’Down. Run2 STDS of
HWDP(heavy weight drill pipe) below c/tester(cup tester). PT TBG(tubing)/spool, make up to 300/2500 PSI, L/D
相关推荐：
loading