There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可识别的命令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列错误命令
The sector size specified in this file is too large: 该文件中指定的扇区太大 The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丢失或被破坏：WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS里有一个无效的国家代码
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS里有一个错误的设置国家命令
There is not enough memory for the COUNTRY.SYS file 没有足够的内存来加载COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 请从CONFIG.SYS文件中删除部分驱动程序，然后再试
Remove some drivers, and then try again 去除一些驱动程序，然后再试。这里的驱动程序是指在CONFIG.SYS中使用device或devicehigh命令加载的程序文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 从你的(CONFIG.SYS)移去部分程序，然后再试
The configuration specified in your CONFIG.SYS file is too large for memory 调整你的CONFIG.SYS文件以获得足够大的内存
You have too many block devices specified in your CONFIG.SYS file 调整你的CONFIG.SYS文件以获得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆栈设置不正确
Default stack settings will be used instead 缺省的堆栈设置将被替代使用 There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS里XX行错误
Warning: Logical drives past Z exist and will be ignored 警告：逻辑驱动器Z已经存在，将被忽略
Type the name of the Command Interpreter (e.g.,
C:\\WINDOWS\\COMMAND.COM) Press any key to continue… 请输入命令解释器的文件名(如：C:\\WIN DOWS\\COMMAND.COM)后，按任意键继续 Windows is bypassing your startup files
Minimal network support will be loaded if available Windows正在跳过你的启动文件。如果网络可用，最小网络支持将被加载
Windows is starting the command prompt only Windows正在启动命令字符模式
Windows will prompt you to confirm each startup command Windows将提示你确认每一个启动命令
The compression driver cannot be set up correctly 压缩驱动程序不能被正确加载
Get a version from your vendor that is compatible with this version of Windows 从你的供应商那里获得一个与Windows版本相兼容的版本 Process the system registry 运行系统注册表
Create a startup log file (BOOTLOG.TXT) 创建启动日志BOOTLOG.TXT文件 Process your startup device drivers (CONFIG.SYS) 运行CONFIG.SYS文件中的设备驱动
Process your startup command file (AUTOEXEC.BAT) 运行AUTOEXEC.BAT中的启动命令
Load the Windows graphical user interface 装入WINDOWS图形用户界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告：Windows检测到一个注册表或配置错误选择DOS操作模式，运行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告：Windows检测到一个访问压缩驱动器错误，选择安全模式下的MS-DOS，来帮助你识别这个问题
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告：
Windows在刚才尝试后不能够完成加载，选择安全模式，用最小驱动启动你的电脑
Warning: Windows multi-boot may not function correctly
Check for system files in your root directory with conflicting extensions 警告：Windows不能够正确完成多系统启动，在你的ROOT目录里检查不一致的系统文件
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告：系统管理器运行失败，一些实模式驱动可能没有正确初始化
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS里BUFFER设置太大。默认的BUFFER缓冲器设置将被使用
A memory allocation error occurred during startup
Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告：高端内存不可用，低端内存将被代替使用
There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 对Windows来说没有足够的内
存，请从CONFIG.SYS文件中移去部分加载的程序，然后再试着启动你的读入计算机
Your previous MS-DOS files were not found. 旧的MS-DOS文件没有找到，这常见于使用双启动的系统，另一个系统是DOS6
Your previous MS-DOS version is not supported. MS-DOS startup failed 旧的MS-DOS版本不支持。MS-DOS启动失败
Now loading your previous version of MS-DOS, please wait 现在正在加载旧的MS-DOS版本，请等待
Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS文件中无效的设置选项。系统堆栈溢出，系统挂起
Change the STACKS setting in your CONFIG.SYS file, and then try again 请改变CONFIG.SYS文件中的STACK设置，然后再试 Stack overflow 堆栈溢出 Integer divide by 0 整数被0除
Not enough space for environment 没有足够的空间 Run-time error 运行错误
Floating-point support not loaded 浮点运算支持没有装入 Null pointer assignment 无效的断点分配
相关推荐：
loading