%LINK-5-CHANGED: Interface GigabitEthernet1/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up Switch> Switch> Switch> Switch>enable Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 1 name engineer
A default VLAN may not have its name changed. Switch(vlan)#vlan 2 name account VLAN 2 added: Name: account
Switch(vlan)#vlan 3 name manager VLAN 3 added: Name: manager Switch(vlan)#exit APPLY completed. Exiting.... Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# Switch(config)#TimesNewRomanPSMT;mso-fareast-font-family:;mso-bidi-font-family:\New Roman\ ^ % Invalid input detected at '^' marker. Switch(config)#mso-ansi-language:EN-US;mso-fareast-language:ZH-CN;mso-bidi-language:AR-SA'>interface ^ % Invalid input detected at '^' marker. Switch(config)#FastEthernet 0/2
^
% Invalid input detected at '^' marker.
Switch(config)# Switch(config)#
Switch(config)#interface f0/2
Switch(config-if)#switchport access vlan 2 Switch(config-if)#interface f0/3
Switch(config-if)#switchport access vlan 3 Switch(config-if)#int g1/1
Switch(config-if)#switchport mode trunk
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Switch(config-if)#
（交换机2）配置：
C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4) Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory. 2960-24TT starting...
Base ethernet MAC Address: 00D0.BA66.89BB Xmodem file system is available. Initializing Flash...
flashfs[0]: 1 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 64016384 flashfs[0]: Bytes used: 4414921 flashfs[0]: Bytes available: 59601463 flashfs[0]: flashfs fsck took 1 seconds. ...done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4
Loading \
########################################################################## [OK] Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team
Image text-base: 0x80008098, data-base: 0x814129C4
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
24 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s)
63488K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00D0.BA66.89BB Motherboard assembly number : 73-9832-06 Power supply part number : 341-0097-02 Motherboard serial number : FOC103248MJ Power supply serial number : DCA102133JA Model revision number : B0 Motherboard revision number : C0
Model number : WS-C2960-24TT System serial number : FOC1033Z1EY Top Assembly Part Number : 800-26671-02 Top Assembly Revision Number : B0 Version ID : V02
CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT 12.2 C2960-LANBASE-M
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Wed 12-Oct-05 22:05 by pt_team
Press RETURN to get started!
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up
%LINK-5-CHANGED: Interface GigabitEthernet1/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up Switch> Switch> Switch> Switch>enable Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode, as VLAN database mode is being deprecated. Please consult user documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 1 name engineer
A default VLAN may not have its name changed. Switch(vlan)#vlan 2 name account
相关推荐：
loading