第一范文网 - 专业文章范例文档资料分享平台

PON设备故障定位指导

来源:用户分享 时间:2025/6/3 11:02:10 本文由loading 分享 下载这篇文档手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:xxxxxxx或QQ:xxxxxx 处理(尽可能给您提供完整文档),感谢您的支持与谅解。

文档名称

内部公开

Vender name SOURCEPHOTONICS Vendor OUI 0006b5

Vendor specific 53 50 53 2d 34 33 2d 34 38 48 2d 48 50 2d 43 44 45 20 20 20 20 20 20 20 20 20 00 00 00 00 00 00 Module type - Module sub-type - Used type - Encapsulation type -

1.3.1 查询EPON 光模块情况

MA5680T(config-if-epon-0/3)#display port state 0

----------------------------------------------------------------------------

F/S/P 0/1/0 Optical Module status Online Port state Offline Last down cause LOS Last up time 2011-01-04 18:59:28+08:00 Last down time 2011-01-04 21:30:35+08:00 Laser state Normal Available bandwidth(Kbps) 1241152 Temperature(C) 9 TX Bias current(mA) 31 Supply Voltage(V) 3.27 TX power(dBm) 5.04 Illegal rogue ONT Existent Max rate(Kbps) 1300000 <-EPON光模块的下行最大波特率是1300000 Max Distance(Km) 20 Wave Length(nm) 1490

2015-5-3

华为保密信息,未经授权禁止扩散

第5页, 共22页

文档名称

内部公开

Fiber type Single Mode Signal detect Normal TX fault Normal Identifier SFP Ext.Identifier GBIC/SFP function is defined by serial ID only Connector SC

Encoding 8B10B <-EPON光模块编码方式一般都是8B10B Length(9um)(Km) 20.0 Length(50um) - Length(62.5um) - Length(Copper) - Cc_base 0x97 CC_EXT 0x91 BR,max Unspecified BR,min Unspecified SFF-8472 Compliance Includes functionality described in Rev 9.4 Diagnostic Monitoring Type Digital diagnostic monitoring Externally Calibrated Power measurement type: Average Power Options TX_DISABLE,and disables the serial output TX_FAULT LOS(signal as defined in SFP MSA) Enhanced Options Alarm/warning flags TX_DISABLE control and monitoring TX_FAULT monitoring Vendor Rev Unspecified Vender PN SPS43GBP2CDFCHW Vender SN AC42001225

2015-5-3

华为保密信息,未经授权禁止扩散

第6页, 共22页

文档名称

内部公开

Manufactured 10-11-06 Vender name SOURCEPHOTONICS Vendor OUI Unspecified Vendor specific 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20

20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 Module type - Module sub-type - Used type - Encapsulation Type -

----------------------------------------------------------------------------

注意光模块类型时必须要max rate和encoding两项条件同时满足

1.4 确认光线路是否存在问题

通过查询ONT和PON口的收发光功率值,结合现网实际的光路组网计算出理论衰减值,对比实际值,如果差异大于3db,可能光路存在问题,需排查光路。 1.4.1 查询ONT光功率情况

MA5680T(config-if-gpon-0/5)#display ont optical-info --------------------------------------------------------------- Rx Optical Power(dBm): -25.37 <-ONT下行光功率,即ONT接收OLT的光功率值 RX power current Warning Threshold(dBm) : [-,-] RX power current Alarm Threshold(dBm) : [-,-] Tx Optical Power(dBm) : 3.15 <-ONT发送光功率

TX power current Warning Threshold(dBm) : [-,-] TX power current Alarm Threshold(dBm) : [-,-] Laser Bias Current(mA) : 21

2015-5-3

华为保密信息,未经授权禁止扩散

第7页, 共22页

文档名称

内部公开

TX bias current Warning Threshold(mA) : [-,-] TX bias current Alarm Threshold(mA) : [-,-] Temperature(C) : 46 Temperature Warning Threshold(C) : [-,-] Temperature Alarm Threshold(C) : [-,-] Voltage(mV) : 3220 Supply voltage Warning Threshold(mV) : [-,-] Supply voltage Alarm Threshold(mV) : [-,-] OLT Rx ONT Optical Power(dBm) : -27.78 <-OLT接收ONT的上行光功率值 CATV Rx Optical Power(dBm)

注意前面5项参数,是OLT到终端上查询出来的值,需要对应的终端 支持

上报光模块信息且必须保证ONT正常上线。如果查询时没有显示,则跟终端类型及版本相关。

1.4.2 查询OLT PON口光功率情况

MA5680T(config-if-gpon-0/5)#display port state

----------------------------------------------------------------------------

F/S/P 0/5/0 Optical Module status Online Port state Online Last down cause - Last up time 2011-06-27 23:56:14+08:00 Last down time - Laser state Normal Available bandwidth(Kbps) 1153034 Temperature(C) 47

2015-5-3

华为保密信息,未经授权禁止扩散 第8页, 共22页

搜索更多关于: PON设备故障定位指导 的文档
PON设备故障定位指导.doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印
本文链接:https://www.diyifanwen.net/c4rqyc4vpj04ddq343h16_2.html(转载请注明文章来源)
热门推荐
Copyright © 2012-2023 第一范文网 版权所有 免责声明 | 联系我们
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ:xxxxxx 邮箱:xxxxxx@qq.com
渝ICP备2023013149号
Top