ESD防静电手册

所有的防静电工作台上的防静电垫应当有唯一的一个编号.此项工作由各事业部根据具体情况由相关部门完成.

5.4.12.7 Any ESD workstations failed is not allowed to use, bad ones shall be repaired by FE. Any dispute for test result shall be analyzed and clarified by QA

任何测试不合格的静电工作台不允许继续使用，不合格的静电工作台必须由FE 进行修复至合格才可续用。关于测试结果的任何争议，由QA 进行最终分析和澄清.

5.4.12.8 All nonessential insulator may cause electrostatic such as plastic cup, plastic bag, personal items should be removed from the ESD workstation or any operation where unprotected ESDS items are handled.

所有非必需的可能造成静电损坏的绝缘体（如：塑胶杯、塑胶袋、个人用品等）必须远离 ESD 工作台面或其它处理未保护的ESDS 物件的操作区域。

5.4.12.9 Handling of process-required insulators 流程所必需的绝缘体的处理 If the field exceeds 2,000 volts/inch, steps shall be taken either: 在静电场超过2000 volts/inch 的情况下，必须采取下列任何一种措施：

a> Separate the insulator from the ESD-sensitive device by a distance of 30cm(12 inches)使绝缘体(如: 显示器,文件夹)离ESDS 产品超过30cm (12 inches),

b> To use ionization or other charge mitigating techniques to neutralize the charge 使用离子化或其他电荷减轻技术来中和电荷

5.4.12.10 If their worksurface will be put ESD products or components to handle or storage etc, mobile equipment (e.g.: changeover vehicle etc.) and storage equipment (e.g. shelving etc.) should be grounding well (may make use of wheel, or grounding chain or

specific line etc.), and their surface grounding spec and frequency should be in accordance with the above worksurface control requirement.

移动设备(如:周转车等)及存储设备(如:货架等)原则上其表面如要放置ESD 产品或零组件来转运或储存等则需进行良好接地(可通过轮子或接地链或专用固定接地线等), 其表面接地电阻规格要求与量测频率与以上之工作台表面监控要求一致. 5.4.13 ESD Marking /ESD 标示.

5.4.13.1 ESD Susceptibility Symbol ESD敏感符号說明

It is a triangle with a line crossing a hand to show that the item is extremely sensitive to electrostatic and marked as ESDS items. It is labeled on the package or storage area of sensitive items( such as IC, transistor, diode, crystal oscillator)

静电敏感符号,呈三角形,里面画有一双被拉一道痕的手,用来表示该物体对ESD 引起的伤害十分敏感,其标示以识别该物体为ESD敏感物.在敏感元件(如IC,电晶 体,二极体,晶振等)包装上或放置区标示.

5.4.13.2 ESD Protective Symbol ESD敏感防护符号说明

It is triangle with a hand in the side and an arc outside to show the item possesses ESDP ability after special designing and is marked as ESDP subject; this symbol is widely used on mats, chairs, wrist straps, and packaging materials. It may also be used on hand tools, handlers, workstations, or other equipment that has been especially designed or modified to provide ESD control.

静电防护符号, 呈三角形, 在三角形周边有一个弧圈, 在三角形内手上的一道痕 没有了, 用来表示该物体经过专门设计具有静电防护能力.其标示经识别该物体 为ESD 防护物; 此符号广泛用于标识ESD 席, ESD 座椅, ESD 手链以及其它 ESD 包装材料等; 同时该标志也应用于工具, 工作台以及其它ESD 提供防护的 设备等物品.\\

5.4.13.3ESD floor tape (Refer to figure 34) 防静电地板胶(如图34) a> Standard Size: width 8CM; Font Arial / 标准尺寸: 宽8CM ;字体Arial b> Purpose : identify EPA area / 目的：用于标识静电保护区域

Figure 34/图 34

5.4.13.4 ESD warning marking (Refer to figure 35) 防静电警示标识(如图35) a> Size: can be adjusted according to actual situation 尺寸: 可根据实际情况调整

b> Use area : hang in the entrance of EPA area / 使用区域: 挂在静电保护区域入口

Figure 35/图 35

5.4.13.5Common grounding point label

a> Stick label for all ESD common grounding points, refer to figure 36 & 37.ESD 公共接地点贴纸, 如图36 和37.

Figure 36/图 36 Figure 37/图 37

b> Round shape and size can be adapted according to the actual situation. 圆形, 尺寸可根据实际情况做调整.

5.4.13.6 All the ESD labels and marking should be intact and legible. 所有ESD 标签或标识需完整而清晰.

5.4.13.7 All the package containing the ESD products or components need have the

ESD susceptibility symbol or ESD protective symbol of marking described above, which shown the packaged products or components are ESD sensitivity body (major for the package containing incoming ESD material or shipping products ),or ESD protective body( major for the package used to handle the ESD material or products in process); the marking that the product or component body need to have shall be defined according to the customer requirement, and all the new purchased ESD package should have the above required ESD marking ,but they must be legible 所有包含ESD 产品或零组件的包装,需具有以上所要求之”静电敏感”或”静电防护”要求的标示,以表示该包装内的产品或零组件为ESD敏感物(主要针对ESD敏感物料厂商来料包装或出货给客户包装), 或此包装是ESD 防护物(主要针对移转用之ESD 包装);.对ESD 敏感产品或零组件本体之ESD 标志,依客户要求为准,所有新购之ESD 包装需确保有以上要求之ESD 标示,但必须清楚可见)

5.4.14 ESD Packaging Material/ESD 包装类材料

(Reference standard 参考标准: ANSI ESD S541; ESD ADV11.2;)

ESD protective packaging shall be in accordance with the contract, purchase order, drawing or other documentation（customer requirements）. When not specified by the above documentation. The ESD coordinator should follow the below guideline to define the ESD protective packaging requirements, both inside and outside the EPA

ESD 保护包装必须与合同，采购单，设计图纸和其他文件中的规定(客户要求)一致，如果没有上述文件规定，ESD 协调员将按照以下方针定义在EPA 内，外的ESD 保护包装要求 5.4.14.1 ESD Packaging Material define method/ESD 包装材料定义方法 a> Inside the EPA /在EPA 内

ESD dissipative & Antistatic material or conductive & Antistatic material /静电耗散性&抗静电材料或导电&抗静电材料 b> Outside the EPA/在EPA 外

Use the Antistatic and Static Shielding material 使用抗静电和屏蔽的材料

c> If the material not use for pack the ESDS but will very near the product in process,recommend it be Antistatic material 如该材料不用于产品包装，只是在生产过程中会接近产品，推荐为抗静电材料