R/W 0 D/I 1 DB7 Busy DB6 0 DB5 DB4 DB3 0 DB2 0 DB1 0 DB0 0 On/Off RESET Busy
When busy is 1, the LSI is executing internal operations. No instruction are accepted
while busy is 1, so you should make sure that busy is 0 before writing the next instruction. ON/OFF
Shows the liquid crystal display condition: on condition or off condition. When on/off is 1, the display is in off condition. When on/off is 0, the display is in on condition
RESET
RESET = 1 shows that the system is being initialized. In this condition, no instructions
except status read can be accepted.
RESET = 0 shows that initializing has system is in the usual operation condition. Write Display Data
R/W D/I DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0 0 D D D D D D D D
Writes 8-bit data DDDDDDDD ( binary ) into the display data RAM. The Y address is
increased by 1 automatically. Read Display Data
R/W D/I DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
1 1 D D D D 1 D D D
Reads out 8-bit data DDDDDDDD ( binary ) from the display data RAM. Then Y address is
increased by 1 automatically.
One dummy read is necessary right after the address setting. For details, refer to the
Y Address012page 0616263X = 0DB0toDB7DB0toDB7page 1X = 1DB0toDB7DB0toDB7page 6X = 6page 7X = 7Figure 1. explanation of output register in ―Function of Each Block‖.
Page 13 of 25 WS-EP-008 10(A)
12.Reliability Content of Reliability Test (wide temperature, -20℃~70℃)
Environmental Test Test Item High Temperature storage Low Temperature storage Content of Test Endurance test applying the high storage temperature for a long time. Endurance test applying the high storage temperature for a long time. Endurance test applying the electric stress High Temperature (Voltage & Current) and the thermal stress to the Operation element for a long time. Low Temperature Endurance test applying the electric stress under Operation low temperature for a long time. The module should be allowed to stand at 60℃,90%RH max High Temperature/ For 96hrs under no-load condition excluding the Humidity Operation polarizer, Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of operation -20℃ 25℃ 70℃ Thermal shock resistance 30min 5min 30min 1 cycle Test Condition 80℃ 200hrs -30℃ 200hrs 70℃ 200hrs -20℃ 200hrs 60℃,90%RH 96hrs Note 2 1,2 —— 1 1,2 -20℃/70℃ 10 cycles —— Total fixed amplitude : 15mm Vibration Frequency : Endurance test applying the vibration during 10~55Hz Vibration test 3 transportation and using. One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes VS=800V,RS=1.5kEndurance test applying the electric stress to the Ω Static electricity test —— terminal. CS=100pF 1 time Note1: No dew condensation to be observed.
Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber.
Note3: Vibration test will be conducted to the product itself without putting it in a container.
Page 14 of 25 WS-EP-008 10(A)
13.Backlight Information Specification
PARAMETER Supply Current Supply Voltage SYMBOL MIN ILED V 264 4.0 － 148.8 ─ － TYP 330 4.2 － 186 573 MAX 420 4.4 8 － － UNIT mA V V TEST CONDITION V=4.2V － － Reverse Voltage VR Luminous Intensity Wave Length Life Time Color
IV λp － CD/M2 ILED=330mA nm Hr. ILED=330mA V≦4.6V 100000 － Yellow Green Note: The LED of B/L is drive by current only, drive voltage is for reference only. drive voltage can make driving current under safety area (current between minimum and maximum).
Page 15 of 25 WS-EP-008 10(A)
14. Inspection specification
NO Item Criterion AQL 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character , dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 0.65 1.5 Current consumption exceeds product specifications. 1.6 LCD viewing angle defect. 1.7 Mixed product types. 1.8 Contrast defect. 01 Electrical Testing 02 Black or white 2.1 White and black spots on display ≦0.25mm, no more than spots on LCD three white or black spots present. (display only) 2.2 Densely spaced: No more than two spots or lines within 3mm 3.1 Round type : As following drawing Φ=( x + y ) / 2 SIZE 0.10＜Φ≦0.20 2.5 Acceptable Q TY 2 2.5 Φ≦0.10 Accept no dense 0.20＜Φ≦0.25 1 LCD black 0.25＜Φ 0 spots, white spots, contamination (non-display) 3.2 Line type : (As following drawing) Length Width Acceptable Q TY --- W≦0.02 Accept no dense L≦3.0 0.02＜W≦0.03 2 L≦2.5 0.03＜W≦0.05 --- 0.05＜W As round type If bubbles are visible, judge using black spot specifications, not easy to find, must check in specify direction. Size Φ Φ≦0.20 0.20＜Φ≦0.50 0.50＜Φ≦1.00 1.00＜Φ Total Q TY Acceptable Q TY Accept no dense 3 2 0 3 03 2.5 04 Polarizer bubbles 2.5
Page 16 of 25 WS-EP-008 10(A)
相关推荐：
loading