EP-MA02使用说明书(7)

Weak: Strong: Approx. 7.0 kPa Medium: Approx. 0.0 kPa Backrest: Approx. 10°– 170° Legrest: Approx. 0°– 80° Approx. 15 min. for both upper and lower body (Approx. 5 minutes for the quick massage) Approx. 110 cm× 80 cm× 10 cm Approx. 61 cm× 80 cm× 168 cm Approx. 6 kg 8 cm× 77 cm× 11 cm Approx. 77 kg Approx. 10 kg 0 cm

Approx. 11.0 kPa

For those who weighing 100 kg or more, the product operations may make more noise and the fabric cover may wear faster.

3-4

2010/07/09

English11:16:36

English

EP-MA02使用说明书

SETTING UP THE UNITWHERE TO USE THE UNITKeep at least 10 cm away from the wall. Approx. 195 cm Width approx. 80 cm Approx. 35 cm Approx. 30 cm Avoid places where the unit will be exposed to direct sunlight for long periods of time or places where it will be exposed to high temperatures, such as in front of a heater, etc., as this can cause discoloration or ha

rdening of the synthetic leather. Placing a mat or cloth under the unit is recommended to prevent floor damage. The size of the mat should be sufficient (at least 10 cm× 70 cm) to cover the areas where the unit touches and where the legrest could touch the floor. Set the unit near the outlet. See Warning No. 10 and 1 on page 1.

3 HOW TO MOVE THE UNIT Grasp the legrest to move the unit when using the wheels. It is easier to move the unit with the massage heads retracted and the backrest in the upright position. *Place a mat or cloth on the floor and move the unit slowly to prevent floor damage.

Using the wheels to move the unit

Move the unit by having one person hold the legrest and another person use the handles on the back. *Please hold the handles and legrest securely to avoid dropping the unit as it may damage your floor.

Lifting the Unit

Move it slowly

LegrestPlace your fingers to the handle

Mat

Wheels

Area where legrest could touch the floor

Area where unit touches the floor

4 INSTALL THE ARMRESTS ON THE UNITBack Front Zipper

1 Install the armrests.the coated fabric.) (Be careful to avoid damaging1 Unfasten the zipper of the armrest completely. 2 Check the side (right or left) of the armrest. Check the direction (front or back) of the armrest as well. The illustration shows the left armrest. The right armrest is stamped“Front”,“Right” and“Back”. *The left armrest must be installed on the left hand side of the unit. 3 Align the convex portion of the armrest with the round hole on the unit, and embed the armrest on the unit. Avoid catching the coated fabric between them. If it is caught, pull it out without damaging the fabric.

1 UNPACK THE UNIT AND RAISE THE BACKREST When raising the backrest, do not allow hands or feet to become caught between the backrest and the backrest latch or the backrest and the armrests. Failure to follow this precaution may result in pinching, which may lead to injury.

CAUTION

Left

Convex

1 When packed for shipping the backrest is folded forward.

Remove the top of the shipping container.

2 Remove the packing and cushioning materials and take out the accessories.Front Backrest latch

Round hole Rear Lift up

the backrest. 3 Raiseconnect the power cord to an electrical outlet during setup. Do not Hold the backrest with both hands and lift in the direction of the arrow until it comes to a stop. Be careful to avoid catching the power cord or the controller cord.

the armrests with attachment screws. 2 Secure positions for a single armrest) (Total ofLift the coated fabric on the side of the armrest and insert the attachment screw onto the end of the Allen key, and then tighten. (Tighten the screws in the positions lightly at first, and then tighten all screws firmly.) *If the screw does not enter into the hole, tighten the screw by pushing the armrest from the top. *When tightening attachment screws 1 and 3, inserting the screws while pushing the covering and inside ure

thane of the armrest up with your thumb will make them easier to tighten. *When tightening attachment screw 2, reclining the backrest will make it easier to tighten.

Check that there is nothing around the unit.

Allen key

Secure with screws

2 INSPECT CONTENTS OF SHIPPING CONTAINERMassage Lounger Pillow Back Cushion Allen Key— 1 Attachment Screws— 8 Lock Switch Key— 1 Front Armrests— 2 The lock switch key has been inserted in the lock switch prior to leaving the factory. Power cord English Rear

3 Close the zipper at the bottom side of the armrests.When closing the zipper, be careful not to twist the end of the zipper. 1 Set the zipper. 2 Fasten the zipper. English

both ends of the 4 Put in the edge of the zipper. zipper into the inside. Turn

5

6

5-6

2010/07/09

11:16:37

EP-MA02使用说明书

5 FIX THE CONTROLLER CORDFix the controller cord with the fastener for securing the controller cord at a position about 45 cm from the connected part of the controller on either the right or left side of the armrest. * Confirm that there is a margin for the controller cord length when the backrest is reclined. (The illustration shows that the cord is attached to the right armrest.)

搜索“diyifanwen.net”或“第一范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读，第一范文网，提供最新教学研究EP-MA02使用说明书(7)全文阅读和word下载服务。